Vbox racerender serial number#
Vbox racerender serial#
Vbox racerender update#
Vbox racerender software#

This is a useful feature when two parts of a track run very close to each other, or the pit lane is next to the start/finish line, as lowering this value can stop the virtual line from being triggered at the incorrect area of the circuit. Gate Width – This configures the width of any gates set in the software. For example, if the trigger speed was 104 km/h then 100 km/h would be the nominated start speed for the corrected brake stop distance.Ĭorrected Distance Start Speed – If you do not select the auto option, you can specify a speed value you want to correct all deceleration tests to. Here you can configure the start and end speed for non-trigger deceleration tests.Īuto Corrected Distance Start Speed – This sets the Speed Sensor to use the nearest rounded 10 km/h speed when the trigger is activated. Message Selection: You can select or deselect NMEA messages for transmission by checking and un-checking the boxes next to each message type.Ĭlick here for VBOX Speed Sensor Serial Output protocols

Vbox racerender update#

Update Rate: You can change the update rate of the NMEA messages by using this drop-down menu.

Vbox racerender serial#

If the NMEA message format is selected, the following options become available.īaud Rate: The required serial baud rate can be selected from this drop-down menu. NMEA: For user-defined NMEA message output. Racelogic : For online connection with VBOX Test Suite.īrake test: For use with Racelogic Brake Test Software. NMEA message format is the only user configurable setup. This selects which format the VBOX Speed Sensor will output the Serial data in. The Leap second value was increased to 18 seconds as of December 2016 – you can find more information about this, here. This is where you can change the update rate of the GPS engine and set a minimum speed output value if required. SBAS – SBAS differential corrections are received from the nearest Geo-stationary GPS-SBAS satellite. This feature gives you the option to enable differential GPS: You can find more information about the CAN output of the Speed Sensors here. These are the different channels available under the different messages. In the Actual column, you can change the ID value, and by ticking the Xtd box behind the Actual ID value you can extend the identifier format from standard 11-bit to extended 29-bit. Default values are the Racelogic standard ID’s of 0x301, 0x302, 0x307, etc.

These columns allow you to modify the CAN IDs transmitted by the Speed Sensor. You can select if a CAN message is switched on/off by ticking or un-ticking this box for the corresponding message. You can find more information about the CAN delay function here. Note: While the unit still transmits all channels, it will stabilise Speed on CAN ID 302 when this feature is enabled. Enabling this feature will fix the CAN latency at 15.5 ms. You can enable or disable the internal CAN termination resistance here.

Vbox racerender software#

The software has 4 common baud rate values: 1 Mb/s, 500 kb/s, 250 kb/s or 125 kb/s. When you have completed your setup or you want to cancel your setup without writing anything to the unit, click on Close to close the setup window. sscfg format.ĭisplays live GNSS data and basic current setup.Īfter making changes to the setup, you must click the Write to unit button to upload the settings to the Speed Sensor. You can save the configuration you set up to a file for later use and you can load a saved configuration file if you have a suitable one already set up. You should only use this when your device is struggling to gain SAT lock. This feature clears the almanac stored in the GPS engine. Technical information about the GPS engine in the connected unit.

Vbox racerender serial number#

This area will provide information about the unit type, software version, serial number and installed firmware version currently being used. This menu contains the Selected com port drop-down, along with a refresh button and a Disconnect button.